Search
Search found 1020 matches
- Tue Feb 06, 2024 6:45 am
- Forum: Ecu and Electronics
- Topic: Venezuelan Civic D16Y4 P2K ECU D4T9404 Distrib
- Replies: 4
- Views: 64864
Re: Venezuelan Civic D16Y4 P2K ECU D4T9404 Distrib
Good info. I was unaware on availability of the stock d14 distributor parts.
- Sun Sep 25, 2022 7:09 am
- Forum: Reliability- Problems
- Topic: d14a4 idle problem
- Replies: 16
- Views: 77667
Re: d14a4 idle problem
Hmmm, the 4-1 header with a non central bung combined with a stock ecu map may be the issue indeed. I once had the same problem but can’t figure what I did that fixed it. It may be the combination of header plus map being off. The perma heated o2 is not my biggest concern. Well controlled o2 heaters...
- Thu May 12, 2022 1:22 pm
- Forum: D14 Engine Tuning
- Topic: Pw0 ECU EJ9
- Replies: 1
- Views: 3735
Re: Pw0 ECU EJ9
Check my OBD1 conversion article... the PW0 ECU is an OBD0 ECU and will require a similar approach. I have done such setups decades ago... but really dig into my ECU pages please.
- Thu May 12, 2022 1:20 pm
- Forum: Engine block
- Topic: D14 Rods dimensions
- Replies: 2
- Views: 3876
Re: D14 Rods dimensions
Nice one, can't add any info now (although I suspect the D13B rod made by Crower somewhere/somewhen in the past may have been a perfect fit, main dimensions and bearings etc. all seemed right). But thats an expensive gamble probably.
- Thu May 12, 2022 1:18 pm
- Forum: Engine block
- Topic: d16a6 head on d14a3/4 block
- Replies: 8
- Views: 7820
Re: d16a6 head on d14a3/4 block
Always, never an issue.
- Thu May 12, 2022 1:15 pm
- Forum: Valvetrain
- Topic: camgear and timing with Y8 cam
- Replies: 2
- Views: 66313
Re: camgear and timing with Y8 cam
Hey man, nobody is right hehehe. Truth is, cam gear is highly advisable since the best setting is to be tuned. Normally I'd say go for retarded 0.5 tooth if there is doubt, never advance. Always when I started on the dyno with a 'proper' timed cam, we ended up retarding the camshaft (note that you n...
- Wed Feb 09, 2022 8:39 am
- Forum: Engine block
- Topic: d16a6 head on d14a3/4 block
- Replies: 8
- Views: 7820
Re: d16a6 head on d14a3/4 block
Neh I meant my Skunk2 D16 VTEC cams, just not engaging the VTEC cam lobes, that gave me a 'non-VTEC' 133 bhp. That was fully tuned to about 7000 rpm for fun. Than fully mapping the VTEC lobes got it to 139 bhp with switchover somewere in the 5000-5500 range, no idea exactly where actually, very subt...
- Sat Feb 05, 2022 1:25 pm
- Forum: Ecu and Electronics
- Topic: D14Z2 harness onto D14A4
- Replies: 3
- Views: 3746
Re: D14Z2 harness onto D14A4
ABS is a completely separate system in terms of wiring running on different looms, there should be no problem leaving it out.
- Mon Jan 31, 2022 9:39 pm
- Forum: Reliability- Problems
- Topic: d14a4 idle problem
- Replies: 16
- Views: 77667
Re: d14a4 idle problem
Sorry if I am walking in circles... is your ECU still bonestock with some piggy-backing or properly tuned? Re-reading this I suddenly realize that this can happen (and probably has happened to me) when the fuel mapping is too far of or even so far of its doing the reversed of what should be needed s...
- Mon Jan 31, 2022 9:34 pm
- Forum: Ecu and Electronics
- Topic: D14Z2 harness onto D14A4
- Replies: 3
- Views: 3746
Re: D14Z2 harness onto D14A4
Hey man, sorry for the late reaction... I probably have your email still lingering around don't I (plan to read my mails in about an hour from this post). But I got a couple of 'no's' coming in unfortunately. D15Z8 is the MA/MB VTEC-E which is more of an EG chassis in terms of wirelooms. So its basi...