Specifications of stock Ecus and electronics

Wiring up and working with the D14 ECUs
User avatar
saxophonias
Posts: 2592
Joined: Fri Jul 03, 2009 6:03 am

Specifications of stock Ecus and electronics

Post by saxophonias »

Codes, obds and pinouts of stock d14 ecus
Last edited by saxophonias on Tue Jul 14, 2009 1:16 am, edited 1 time in total.

User avatar
Dodo Bizar
Site Admin
Posts: 2009
Joined: Mon Jun 22, 2009 10:36 pm

Re: Specifications of stock Ecus

Post by Dodo Bizar »

EDM P3X (D14A3) and P3Y (D14A4)

In this post the OBD (OBD2a?) sheme of the Sfi (Simplified Fuel injection) engines D14A3/A4 are presented EDM (Europen Domestic Market) style. Some connections are different from car to car. Those are marked grey. These pinouts are very alike pinouts that used for certain D16 engines in Australia and certain D15 engines in the Middle East. The exact specs of these engines are unknown to me. However, these pinouts may be helpful for more people besides D14A3/A4 owners. Note that the connectors are the same as the A and D connector from the OBD1 ECU’s. However, the numbering has changed to OBD2a style.
Image

Nomenclature:
ACC - A/C relay
ACS - A/C switch
ALTC - Alternator relay, for control purposes, not present on all ECU’s
ALTF - Alternator switch
BKSW- Brake switch, for control purposes, not present on all ECU’s
ECT - Engine coolant temperature
ELIMA- Electric load detection, not present on all ECU’s
FANC - Fan relay, for control purposes, not present on all ECU’s
FLR - Fuel relay
IACV - Idle air control valve, controls the 3 wire type IACV valve, (N)egative and (P)ositive control
IAT - Intake air temperature
IGPLS- Ignition pulses, 1 is always present, 2 can be ignored
IGP - Battery feed, only active when key is turned
IGR - Engine speed
IMO - Checks IMO code of the key and activates FLR if correct
INJ - Injector, the numbers refer to the pair of cylinders connected (1 is on the side with the belts)
LG - Ground for battery circuit
MAP - Manifold absolute pressure
MIL - Motor indication light, this one gives the control engine light (CEL) signal
PCS - Control solenoid, this one is for the small black cylindric valve on the back of the IM
PG - Ground for battery circuit
PSP. - Power steering switch, not present on all ECU’s
O2S - Oxygen sensor (lambda sensor) signal
SCS - Service connector switch, checks if the SCS connector is hot wired (for reading engine error codes)
SG - Ground for 5V circuit, 1 is for the MAP sensor, 2 is for the other sensors
STS - Starter switch
TDC - Top dead centre
TPS - Throttle position signal
TXD. - Diagnostic connector, communication signal to the 3 wire connector next to the SCS connector
VBU - Back up battery feed, always active (unless battery is removed)
VCC - 5V feed, 1 is for the MAP sensor, 2 is for the other sensors
VSS - Vehicle speed sensor

User avatar
saxophonias
Posts: 2592
Joined: Fri Jul 03, 2009 6:03 am

Re: Specifications of stock Ecus

Post by saxophonias »

Some Fuse diagrams
Image
Image
Image

User avatar
ilya
Posts: 565
Joined: Wed Aug 05, 2009 1:27 pm
Location: Russia
Contact:

Re: Specifications of stock Ecus and electronics

Post by ilya »

viewtopic.php?f=7&t=359 how2swap IM
EJ9 Russian Helper http://www.ej9.ru
Full Scheme SFI-OBD1 PDF [ENG]
SofRom 1.15 R2 - Chippest RTP Emulator like Hondata S300 and Moates Ostrich

Firebass
Posts: 351
Joined: Wed May 26, 2010 8:35 pm
Contact:

Re: Specifications of stock Ecus and electronics

Post by Firebass »

does any1 have the pin names on ECU of d14z2 ?
Up the Rev Limiter !!!!!!

User avatar
Dodo Bizar
Site Admin
Posts: 2009
Joined: Mon Jun 22, 2009 10:36 pm

Re: Specifications of stock Ecus and electronics

Post by Dodo Bizar »

Check my OBD2b page which says D15Z6. Your D14Z will be similar to that.

Firebass
Posts: 351
Joined: Wed May 26, 2010 8:35 pm
Contact:

Re: Specifications of stock Ecus and electronics

Post by Firebass »

Dodo Bizar wrote:Check my OBD2b page which says D15Z6. Your D14Z will be similar to that.
got any link ?
Up the Rev Limiter !!!!!!

User avatar
Dodo Bizar
Site Admin
Posts: 2009
Joined: Mon Jun 22, 2009 10:36 pm

Re: Specifications of stock Ecus and electronics

Post by Dodo Bizar »

I sent you the link, but next time don't go to the forum directly ;). Route via www.dodo-upgrades.nl, then you see the pages I mentioned, listed in the left. (And I get a visitor count for it :D.)

Firebass
Posts: 351
Joined: Wed May 26, 2010 8:35 pm
Contact:

Re: Specifications of stock Ecus and electronics

Post by Firebass »

yo guys i was trying to find out if my ecu is japan made or euro. i opened the plastics and i saw on the barcode of the ecu something KEIHIN is that the firm of the ECU ? i checked the code is P3X any1 knows a clue about it ?
Up the Rev Limiter !!!!!!

User avatar
saxophonias
Posts: 2592
Joined: Fri Jul 03, 2009 6:03 am

Re: Specifications of stock Ecus and electronics

Post by saxophonias »

Image
Image
ob2b ej9 ecu

Post Reply