Aftermarket Rod and Pistons.

User avatar
saxophonias
Posts: 2592
Joined: Fri Jul 03, 2009 6:03 am

Aftermarket Rod and Pistons.

Post by saxophonias »

At this topic we are going to present the possible options available.

hondaNickx
Posts: 713
Joined: Wed Aug 05, 2009 1:06 am
Location: Belgium

Re: Aftermarket Rod and Pistons.

Post by hondaNickx »

Crower sells D13 rods and they are the same rods the D14 uses ;)
Quote from Endyn:"The combustion chamber is a better shape than the DOHC.So don't chunk those 1.6 SOHC engines, they can make really good power. For a pure performance application, regardless of application, I'd choose the SOHC. No bull!"

User avatar
saxophonias
Posts: 2592
Joined: Fri Jul 03, 2009 6:03 am

Re: Aftermarket Rod and Pistons.

Post by saxophonias »

Are they of good quality or like their cams that tend to crack :roll: :roll:
Good info however, especially for the turbo guys

User avatar
SquirtAndSpark
Posts: 172
Joined: Wed Aug 05, 2009 9:39 am

Re: Aftermarket Rod and Pistons.

Post by SquirtAndSpark »

hondaNickx wrote:Crower sells D13 rods and they are the same rods the D14 uses ;)
i can't find this...

User avatar
saxophonias
Posts: 2592
Joined: Fri Jul 03, 2009 6:03 am

Re: Aftermarket Rod and Pistons.

Post by saxophonias »

Are we talking about these?
http://crower.com/cgi-bin/detail.cgi?prod_id=B93742B-4
http://crower.com/cgi-bin/detail.cgi?prod_id=ML93742B-4

they are for 1.3cc honda engines but not d13 as far as i can tell.
You can always customise rods but i'll be more expensive.

User avatar
Dodo Bizar
Site Admin
Posts: 2009
Joined: Mon Jun 22, 2009 10:36 pm

Re: Aftermarket Rod and Pistons.

Post by Dodo Bizar »

Yeah that should be the one.

http://crower.com/pdf/2008b/188-189.pdf

For more specs.

Thing I doubt now is P.E. and B.E. thickness numbers.
B.E. I believe will be okay.

But P.E. thickness is different from D16 rods (see same chart). Difference is just 0.710 versus 0.716 inch but still I doubt is this bad? Since I am looking for D16 pistons... is this play important... or is it even disastrous? Does it fit snuggly or is it a loose fit? Diff is 0.15 mm.

hondaNickx
Posts: 713
Joined: Wed Aug 05, 2009 1:06 am
Location: Belgium

Re: Aftermarket Rod and Pistons.

Post by hondaNickx »

Dodo Bizar wrote:Yeah that should be the one.

http://crower.com/pdf/2008b/188-189.pdf

For more specs.

Thing I doubt now is P.E. and B.E. thickness numbers.
B.E. I believe will be okay.

But P.E. thickness is different from D16 rods (see same chart). Difference is just 0.710 versus 0.716 inch but still I doubt is this bad? Since I am looking for D16 pistons... is this play important... or is it even disastrous? Does it fit snuggly or is it a loose fit? Diff is 0.15 mm.

You're right Joris i didn't even noticed that they have a little difference.If you would use D16 pistons your piston pin has less play .You could always get 0.075mm from both size of the piston off.You'll need to check how much play aftermarket d16 pistons have or oem pistons.I think Arias pistons for a d16y8 would be great ,except that they have a Compression height of 29.3 and sit 0.2mm below deck.
Crower makes absolute great rods the crower Maxi Lights are very light and strong and would be perfect for a build D14 N/A engine.
Quote from Endyn:"The combustion chamber is a better shape than the DOHC.So don't chunk those 1.6 SOHC engines, they can make really good power. For a pure performance application, regardless of application, I'd choose the SOHC. No bull!"

demolik
Posts: 42
Joined: Thu Aug 06, 2009 3:41 pm

Re: Aftermarket Rod and Pistons.

Post by demolik »

I might be wrong but as I know Suzuki Vitara pistons give good results in d16
f.ex.
http://www.civicland.com/forum/forced-i ... stons.html

You can find some porject with this setup on youtube, most of them are turbo

User avatar
Raimundo
Posts: 57
Joined: Wed Aug 05, 2009 2:05 am

Re: Aftermarket Rod and Pistons.

Post by Raimundo »

Demolik, that is because Suzuki Vitara pistons, being 75mm wide are compatible with D Series STD engines, but they lower CR values to just slightly higher than 8:1.
95' Honda Civic
EDM D14A2

User avatar
saxophonias
Posts: 2592
Joined: Fri Jul 03, 2009 6:03 am

Re: Aftermarket Rod and Pistons.

Post by saxophonias »

I think they have them as a cheap and strong alternative for turbo set ups right?

Post Reply