[LOOK IT] Step 1. Swap IM D16 + Automatic Addon

User avatar
ilya
Posts: 565
Joined: Wed Aug 05, 2009 1:27 pm
Location: Russia
Contact:

[LOOK IT] Step 1. Swap IM D16 + Automatic Addon

Post by ilya »

pls correct my english :oops:

In this topic, I will try to tell how it was done, with lots of photos. I'll add text later.
wish what would you ask that something extra, and ruled my broken English.

PS. Thanks to all the guys who responded to my messages and questions: saxophonias, DoDo, mynameisowen, LAW, Slavix and other's =) TNX!

CONTINUE PART 2 - ADDED VTEC
viewtopic.php?f=7&t=382
Last edited by ilya on Mon May 02, 2016 12:03 pm, edited 7 times in total.
viewtopic.php?f=7&t=359 how2swap IM
EJ9 Russian Helper http://www.ej9.ru
Full Scheme SFI-OBD1 PDF [ENG]
SofRom 1.15 R2 - Chippest RTP Emulator like Hondata S300 and Moates Ostrich

User avatar
ilya
Posts: 565
Joined: Wed Aug 05, 2009 1:27 pm
Location: Russia
Contact:

Re: [LOOK IT] PART 1. Swap IM D16 + Automatic Addon

Post by ilya »

First I will tell about the differences. the versions of IM. TB and other things.
#
#
#
D16 rail UP, D14 rail DOWN
Image
D14
Image
D16, fuel hose dosn't feet from d14 to d16. inner radius, structure, end of the hose is different. same difference is in receipt of fuel.
in D14, through a hole in the side of fuel falls directly into the hose.
in D16 fuel passes through the end, fighting off the big yellow nuts and gets into the hose.
Image
This pressure fuel rail. Model NR-1. it is always (almost) use of D series ... But! form is slightly different. use only their!
D16 LEFT SIDE.
D14 RIGHT SIDE.
Image
TB GASKET'S
D16 LEFT SIDE.
D14 RIGHT SIDE
Image
Image
Version IM -4
Image
My D16Z6 IM version -3 (with extra hose, close it!)
Image
Image

installed ! WOHOO :
Image
my first picture, sorry for the blue ribbon, no brackets for the filter.
Image
Thus, one must unscrew the fuel hose, otherwise you will break the mounts.
upper key push in the right
lower in left. are holding this "fuel bank". name?
green hose - i dont use it)) II just put that fluid was not flowing during installation.
Image
can see the fuel hose? at the top, I turned it a bit (via attachment), at the bottom, I "bit off" the two locks (on the D14 photo available). and as I was a little loosened up. otherwise too short. repeat.
D14 hose is not suitable for D16 rail! if you want to save, try to drill holes for fasteners D16. but it is not very good! (Rails can bend, aluminum) with further tuning, you'll need to change the rail. otherwise the volume is not enough for injection.
Image
Image
I could catch TB D14, carefully disconnected the RACV. And what I see? " I see that the two form a loop of hose just fluids. so TB does not need to connect 2 hose cooling. spend it directly.
Image
BOLT. close some extra hole in IM (version -03... in -04 it's closed!)
Image
In autumn, I have installed IM D16, but my problem was getting antifreeze in the block. smoke was gray! had to be changed to D14, wait for spring. Now I use sealant. I think this is the only place where the fluid gets into the block.
Image
Last edited by ilya on Wed Apr 20, 2011 6:42 am, edited 8 times in total.
viewtopic.php?f=7&t=359 how2swap IM
EJ9 Russian Helper http://www.ej9.ru
Full Scheme SFI-OBD1 PDF [ENG]
SofRom 1.15 R2 - Chippest RTP Emulator like Hondata S300 and Moates Ostrich

User avatar
mynameisowen
Posts: 1307
Joined: Thu Aug 20, 2009 3:38 am
Location: London or Oxford, England
Contact:

Re: [LOOK IT] PART 1. Swap IM D16 + Automatic Addon

Post by mynameisowen »

Great pictures and topic. Im looking forward to your explanations. did you re-route the coolant from the thermostat straight to the head? Where did you get a coolant hose to fit??
1996 EJ9 Civic
1998 BB8 Prelude Motegi VTi
1998, B16A2 EK4 Civic VTi

Aims:
EJ9 - Now my GF's car.
BB8 - Rebuild after crash damage to front end.
EK4 - Daily driver. Strip and track prep once prelude project complete

User avatar
ilya
Posts: 565
Joined: Wed Aug 05, 2009 1:27 pm
Location: Russia
Contact:

Re: [LOOK IT] PART 1. Swap IM D16 + Automatic Addon

Post by ilya »

I hope to understand what you mean. (Show on my photos please)
Almost all the hoses I purchased in the normal auto-shop. just watched the radius. clamped with clamps. connections throughout the car also the same, so all come. I did not do redirects, I simply deleted the connection TB, and merely one hose.

some updates, i make it for EJ9 99 but it ident with <98


Image
---.
Image
---
Image
Last edited by ilya on Wed Apr 20, 2011 6:42 am, edited 2 times in total.
viewtopic.php?f=7&t=359 how2swap IM
EJ9 Russian Helper http://www.ej9.ru
Full Scheme SFI-OBD1 PDF [ENG]
SofRom 1.15 R2 - Chippest RTP Emulator like Hondata S300 and Moates Ostrich

User avatar
cad civic mechanic
Posts: 140
Joined: Mon Jan 18, 2010 8:08 pm
Location: Bangor N.I

Re: [LOOK IT] PART 1. Swap IM D16 + Automatic Addon

Post by cad civic mechanic »

ilya wrote:I hope to understand what you mean. (Show on my photos please)
Almost all the hoses I purchased in the normal auto-shop. just watched the radius. clamped with clamps. connections throughout the car also the same, so all come. I did not do redirects, I simply deleted the connection TB, and merely one hose.
very nice job, will help me alot when modding my im 8-)
Dont slack her till you wreck her, horse on regardless

User avatar
BETEK
Posts: 1213
Joined: Wed Oct 21, 2009 10:09 am

Re: [LOOK IT] PART 1. Swap IM D16 + Automatic Addon

Post by BETEK »

Well done, nice job ;)
What about the cables, did you extend them? Which one?

User avatar
ilya
Posts: 565
Joined: Wed Aug 05, 2009 1:27 pm
Location: Russia
Contact:

Re: [LOOK IT] PART 1. Swap IM D16 + Automatic Addon

Post by ilya »

cables? cable transmissions not. throttle cable to make it shorter (set of CRX).
all the other hoses are changed, bought, cut, not HONDA) standard. for any car. simply observe the size. AND ALWAYS USE CLIPS FOR END OF THE HOSE!
Last time I did not lay down a clip and I was leaving the coolant.
viewtopic.php?f=7&t=359 how2swap IM
EJ9 Russian Helper http://www.ej9.ru
Full Scheme SFI-OBD1 PDF [ENG]
SofRom 1.15 R2 - Chippest RTP Emulator like Hondata S300 and Moates Ostrich

User avatar
BETEK
Posts: 1213
Joined: Wed Oct 21, 2009 10:09 am

Re: [LOOK IT] PART 1. Swap IM D16 + Automatic Addon

Post by BETEK »

I wanted to say wires.

Law_
Posts: 1154
Joined: Wed Aug 05, 2009 3:37 pm
Location: Portugal

Re: [LOOK IT] Step 1. Swap IM D16 + Automatic Addon

Post by Law_ »

very good review ! congrats ;) cheers ;)

User avatar
saxophonias
Posts: 2592
Joined: Fri Jul 03, 2009 6:03 am

Re: [LOOK IT] Step 1. Swap IM D16 + Automatic Addon

Post by saxophonias »

thanks for sharing man!

Post Reply